Downloaded latest verstion of Melcodiag
I/F is ELM 327 v 1.5 as detected by MD
Comm driver installed without issue
Speed is 38400
ECU set to M3C
Could not request license due to Missing Data
Selector switch on I/F set to SH
Key Switch is on, Not Engine
Debug Output:
"File generated On 7/11/2026 5:48:41 PM"
"Software version 2.0.5.1"
"ELM version : ELM327 v1.5"
"Auto Detect Bike = "
"User Bike = 1100 EVO / 2012"
"CAN Bike = "
"Ecu = N/A"
"Hardw = CAN ERROR"
"Softw = CAN ERROR"
"OilService = NO"
"DesmoService = NO"
"
6 PIDS active founds
080_0000000000000000
081_01000000C8000000
010_C800000000000000
018_00E1000000000000
020_0000060000000000
100_E000000000000001
"
"Vin = CAN ERROR"
"DTC = "
"4EB59B1D"
"Bike = 4"
"lic not found
PaniVIN:
MultiVIN:
M3dVin:
DashVin2:
DashVin:
EcuVin:
"
"not registered"
Assistance Requred.
EVO 1100 Not communicating properly
Forum rules
Do not send PM , if your can't find your problm , please open a new thread with your bike and issue
Do not send PM , if your can't find your problm , please open a new thread with your bike and issue
Re: EVO 1100 Not communicating properly
the CAN ERROR message is not good at all .
Have you tried the other switch position ?
Have you tried the other switch position ?
Re: EVO 1100 Not communicating properly
Yes, the other position, and also oher speeds. Everything but the current setting resilts in popups complaining that communications is not working.
In this setting at least I get a lot of blinking green and yellow lights.
If i switch to the "all bikes" setting I also get a lot of blinking lights, but still, lots of missing data.
In this setting at least I get a lot of blinking green and yellow lights.
If i switch to the "all bikes" setting I also get a lot of blinking lights, but still, lots of missing data.
Re: EVO 1100 Not communicating properly
what data are you getting ?
an other report with this setting will help
an other report with this setting will help
Re: EVO 1100 Not communicating properly
Here is the data with the "Any Bike" ECU setting.
"File generated On 7/12/2026 11:30:23 AM"
"Software version 2.0.5.1"
"ELM version : ELM327 v1.5"
"Auto Detect Bike = "
"User Bike = 1100 EVO 2012"
"CAN Bike = "
"Ecu = N/A"
"Hardw = N/A"
"Softw = N/A"
"OilService = NO"
"DesmoService = NO"
"
7 PIDS active founds
081_01000000C8000000
010_C800000000000000
080_0000000000000000
020_0000060000000000
018_00B1000000000000
100_E000000000000001
211_42880042D000005B
"
"Vin = "
"DTC = "
"4EB59B1D"
"Bike = 7"
"lic not found
PaniVIN:
MultiVIN:
M3dVin:
DashVin2:
DashVin:
EcuVin:
"
"not registered"
"File generated On 7/12/2026 11:30:23 AM"
"Software version 2.0.5.1"
"ELM version : ELM327 v1.5"
"Auto Detect Bike = "
"User Bike = 1100 EVO 2012"
"CAN Bike = "
"Ecu = N/A"
"Hardw = N/A"
"Softw = N/A"
"OilService = NO"
"DesmoService = NO"
"
7 PIDS active founds
081_01000000C8000000
010_C800000000000000
080_0000000000000000
020_0000060000000000
018_00B1000000000000
100_E000000000000001
211_42880042D000005B
"
"Vin = "
"DTC = "
"4EB59B1D"
"Bike = 7"
"lic not found
PaniVIN:
MultiVIN:
M3dVin:
DashVin2:
DashVin:
EcuVin:
"
"not registered"
Re: EVO 1100 Not communicating properly
Good News1.
I got it to work.
I have a Monster 696 as well.
I tried using that and got pretty much exactly the same resuits.....even when I tried with the Key OFF.
I did not believe that to be right.
Tried other USB ports, and finally found one that would work.
I have submitted for both licenses.
The EVO reports "Vin = 0060457571 "
The 696 reports "Vin = 0060229322 "
I got it to work.
I have a Monster 696 as well.
I tried using that and got pretty much exactly the same resuits.....even when I tried with the Key OFF.
I did not believe that to be right.
Tried other USB ports, and finally found one that would work.
I have submitted for both licenses.
The EVO reports "Vin = 0060457571 "
The 696 reports "Vin = 0060229322 "