MYS 1200S DVT 2017 ISSUE

[semtexale]

Hi everyone.
trying to create the file for registering the software, I get an error. This is the log below. I think it doesn't read the ECU, could it be? It's a 2017 MTS 1200S DVT. Thanks for your help.

"File generated On 25/09/2025 19:30:56"
"Software version 2.0.4.8"
"ELM version : ELM327 v1.5"

"Auto Detect Bike = MTS1200"
"User Bike = multistrada 1200s 2017"

"CAN Bike = "
"Ecu = "
"Hardw = "
"Softw = 10SW037916U"
"OilService = YES"
"OilService = NO"
"DesmoService = NO"

" vin DATA
vin DATA
vin 135A905A444D414130304141484230313637323155
vin 7F1A1255555555
vin 7F1A1255555555
vin 0C5A953130535730333739313655

14 PIDS active founds

022_000000000003F4D5
023_000000FC7FCB0401
188_80138017806F441C
020_8000950000004A78
360_38E03325092500FF
018_0002A0008200667D
019_960960000000069D
300_3E980004267D8AFC
174_16800000626A0C52
024_00000B3E00203066
080_2BC0000020A0002C
100_C71202A027000072
178_4680052606800C0B
17C_00000000CA950C2
"
"Vin = ZDMAA00AAHB016721"
"DTC = "
"D6F785B8"
"Bike = 2"
"lic not found
ZDMAA00AAHB016721
"
"not registered"

[jpl250rs]

you don't need to create a file for registering .
if you press the get licence button , it shall open the registration webpage will all data alredy there , you only need to completewith your email and the bike model / year.
As ecu is empty in the 1st line of the prefilled data , it may fail , and if it fail , you can try to write in the first line no data
then it should by pass the check

[semtexale]

I tried as you say but it gives me the same error.
I try to attach a photo of fields.

[jpl250rs]

it looks ok
you can retry i made some changes

if it's still not working
the best is maybe to paste the registration link here , it's paste into the clipboard when you press blue button , i'll have a check with the same data as yours

[semtexale]

Thanks for the help. I did the procedure again and this time it went well, I received the license which I put in the same folder as the software. I restarted the application with the motorbike engine running. However, I noticed that my parameters detected are totally wrong (engine temperature, ambient temperature, engine rpm and even the total km are wrong). It also won't reset my annual service. How can I proceed? Thank you.

[desmo32]

Hi,

Same Problem with my multistrada 1200 dvt.

Any ideas ?

[jpl250rs]

lives values are not decoded for all bikes , if you have strange data , then you can go in the passive tab and monitor different PID to try to identify which pid is the right one and where the correct value is hidden .
i will try to record a video to explain it better

[FrancescoG]

Buongiorno, stesso problema, mts 1200 2017, licenza ricevuta ma non vedo nel campo ecu nessun dato, provando con il reset service niente da fare, il pc fa il suono dell’errore e non sparisce dal Dashboard

[Desmobiwan]

Hello, same problem as Francesco. Successfully connected after received the license, but can't reset service light on dash board on my 1200DVT 2016. Just an "error ring" on my pc.